Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Access Control in Oak Point, TX - What It Costs and Who Fixes It Right
Gate access control in Oak Point typically runs $350-$950 for a new keypad or intercom install, while full smart-access systems on custom driveway gates run $1,400-$2,800 depending on the operator, wiring, and hardware. Our crew answers the phone live 24/7, and we quote the price before any work starts - not after. Nobody wants a surprise invoice at the bottom of a finished ticket, and we don’t work that way.
Hal Gatewood founded Gatewood Fence & Gate in 2001 and still runs the shop. When you call (979) 291-0947, a real person picks up - not a voicemail, not a call center three states away. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Why Oak Point Homeowners Call Us for Gate Access Control
Oak Point is not like most DFW suburbs. It’s an upscale, newer-growth community on the eastern shore of Lake Lewisville, where large private lots with custom automated driveway gates are standard. Buyers here didn’t get a cookie-cutter swing gate from a national trunk-slammer. They got ornamental iron, matched intercom panels, underground operators, and electronics that have to survive North Texas clay and lake humidity. When those systems fail, the neighbors talk. And our name comes up.
We serve Oak Point regularly, and we know that a gate that dragged last March will likely drag again next March unless the post is corrected, not just the hinge. Our Gate Access Control team has been welding on-site and recalibrating operators in Denton County for years. We don’t haul your gate off to a shop. We fix it in your driveway, in the window we promised.
Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right - one call brings Hal back, no runaround. That’s not a marketing line. It’s stamped on every invoice.
Our Gate Access Control Services in Oak Point
Keypad Entry
Keypads on Oak Point gates take a beating from sun, rain, and lake humidity. A keypad that works intermittently is usually a corroded wire nut or a failing membrane switch. A typical keypad replacement or retrofit in Oak Point runs $180-$420, including programming and wiring. We install wired and wireless keypads and match the finish to your existing gate hardware where possible.
Remote Control
When your remote stops opening the gate from the street, the issue is usually the receiver, not the remote. On properties near Lake Lewisville, we often find moisture in the receiver housing from condensation. We test the signal, replace the receiver or reprogram the remotes, and make sure the range actually reaches your driveway apron - because a remote that only works from 15 feet is not a remote, it’s a key with a battery. Remote reprogramming and receiver swaps in Oak Point generally run $120-$260.
Phone Entry
Phone entry systems let you buzz a gate open from your cell, or let a delivery driver call a number that rings your phone. On Oak Point’s larger lots, these save you a walk down a long driveway. We install and program phone-entry modules that integrate with existing swing and slide operators. Most phone-entry installs run $400-$800, depending on the operator brand and cellular module. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Card Reader
Card readers show up on homeowner-association entrances and on private drives with frequent guests or staff. In Oak Point, we see proximity readers and Wiegand readers. When a card reader stops reading, it’s often a ground fault or a failed power supply. We diagnose the reader, the controller, and the wiring between them. Card-reader repair and replacement typically lands between $250 and $550 in Oak Point.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Oak Point
We carry parts for FAAC, BFT, Linear, and Viking operators, plus the usual LiftMaster and Ghost Controls components your builder probably installed. That means when we diagnose a bad control board or a stripped gear, we usually have the part on the truck or can get it the same week - not “sometime next month.” For Oak Point customers, that means less time with a gate stuck open at night, and less time with a gate stuck closed while the Amazon truck idles on the shoulder of FM 720.
Common Gate Access Control Problems We See in Oak Point Homes
- Gate binds on the latch post after a wet winter - Denton County’s Blackland Prairie clay swells with winter rain, and the ground near Lake Lewisville stays wetter than inland DFW. Hinge posts heave and torque, and a swing gate that cleared fine in October starts scraping by March. Post-plumb correction is the fix, not hinge shims.
- Surface rust on ornamental iron gates - Lake humidity accelerates oxidation on gates just a few miles from the water. Rust seizes hinges and weakens welds. We grind, weld, and re-coat on site.
- Safety photocells reversing the gate for no reason - When a post shifts, the photocell beam goes out of alignment and the gate reverses mid-cycle. Re-aligning the sensors only works if the post is corrected first. We do both.
- New keypad that won’t hold programming - Oak Point gets hard rain and heat, and a keypad mounted without a weather hood or with a poor seal will lose its memory. We replace junk installs with properly sealed units and test them before we leave.
Pricing for Gate Access Control in Oak Point, TX
Here’s what we actually see in Oak Point, not a national average. Keypad entry: $180-$420. Remote and receiver service: $120-$260. Phone entry install: $400-$800. Card reader repair: $250-$550. Video intercom install: $900-$2,200. Full smart-access conversion with phone control, intercom, and camera: $1,400-$2,800. A gate post reset near the lake: $600-$1,500 depending on footing depth and gate weight.
We give the price before we start. If you have a written estimate from another company, bring it - we’ll give a free second opinion. There’s no trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Call (979) 291-0947 and you’ll get a real person who can tell you the real number.
We Also Serve Cities Near Oak Point
Our crews cover Oak Point and the surrounding area, including Prosper, Plano, Allen, and Frisco. If you’re just outside Oak Point, we’re still close. Dispatch and scheduling are coordinated from the brand’s Dallas-Fort Worth office, and the crew that shows up knows the roads and the soil.
Serving Oak Point, TX - Our Local Coverage Area
We’re based in the Oak Point area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Oak Point
The clay under your hinge post expands with winter moisture, and the post heaves out of plumb. Near Lake Lewisville, the ground holds moisture longer, so the movement is worse than inland. We pull the footing, re-set the post deeper, and realign the gate - not just shim the hinge. Call (979) 291-0947 for an exact look; estimates are free.
Yes. Most video intercom panels work with existing swing or slide operators, including LiftMaster, FAAC, and BFT. We mount the intercom, run the wiring, and tie it into your phone. In Oak Point, a typical video intercom install on an existing gate runs $900-$2,200. Call (979) 291-0947 for a quote on your gate.
Often yes. When the post shifts, the beam goes out of line. The operator is doing its job - it sees an interruption and reverses. We check the photocell alignment, but if the post moved, the sensor is a symptom. We fix the post, then re-set the sensors. That’s the order that lasts.
Every 12 to 18 months. Near the lake, the clay moves enough that a gate can drift out of plumb between inspections. A quick check catches a leaning post before it strips a gear or cracks a weld. It’s cheaper than a full operator replacement.
Yes. We pull the old keypad, install a smart controller, and set up phone-based entry with a mobile app. Your phone becomes the remote. In Oak Point, a full smart-access conversion runs $1,400-$2,800 depending on the operator and whether you want a camera intercom. Call (979) 291-0947 and we’ll price it from your gate, not a catalog.
Oak Point’s Clay Soils and Lake Humidity Are Hard on Gate Automation
Here’s something most gate companies won’t tell you: in Oak Point, we routinely find 3-to-5-year-old gate installations that already need post-plumb correction. The Blackland Prairie clay near Lake Lewisville’s watershed moves aggressively - it swells in wet springs and shrinks through summer droughts, and that cycle slowly torques gate posts out of line. The result is a swing gate that drags, a rack and pinion drive that strips, or a slide gate that binds on its track. It’s not a cheap install. It’s the soil doing what North Texas soil does.
On Woodland Hills Drive, our crew serviced a LiftMaster swing gate with a rack and pinion drive where the hinge post had heaved out of plumb from wet spring clay. We pulled the post footing, re-set it with deeper concrete, then recalibrated the operator and loop detector so the gate closed without dragging. That job didn’t need a new operator. It needed a correct post. That’s the difference between replacing and repairing.
Lake humidity adds another layer. Ornamental iron gates within a mile or two of the shore rust faster than gates in inland DFW suburbs. We see seized hinges and sagging panels that started as a little surface rust two years ago. We weld, re-coat, and keep the gate running rather than selling a new one.
High-End Gates Deserve High-End Gate Access Control
Oak Point isn’t a place where a cheap keypad bolted to a fence post cuts it. These are custom-fabricated gates, often matched to the house, with ornamental details, underground operators, and intercom panels that visitors actually use. When we install gate access control here, we’re working around your home’s architecture, not just hanging a box. The keypad goes where your hand naturally reaches from the driver’s window. The intercom camera points where a visitor actually stands. The wiring runs hidden, not zip-tied to a post cap. These details matter, and they’re why we treat every Oak Point job as its own project, not another stop.
Call Gatewood Fence & Gate for Gate Access Control in Oak Point
If your gate is binding, your keypad is dead, or you want phone entry without standing in the rain pressing buttons, call (979) 291-0947. A real person answers, day or night. We’ll schedule a time, show up in the window, and hand you a written price before any tool comes off the truck. Free estimates, no trip charge in the county, and a 90-Day Done Right Promise that’s not fine print. That’s how we’ve done it since 2001.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, fixing gates in Denton County since 2001.