Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Oak Point
Most gate repair calls we take from Oak Point come down to two things: a hinge post that’s no longer plumb, or a weld that finally gave way after years of clay soil pushing against it. Hinge replacement in Oak Point typically runs $180-$340 per hinge post, and custom welding work usually falls between $120 and $400 depending on the extent of the repair. If your gate is dragging, binding, or sagging off the post, call (979) 291-0947 and we’ll get someone to your driveway, assess what’s actually failed, and quote the fix before any work starts.
We know Oak Point’s streets, not just its map coordinates. Homes off Lakeshore Drive, around the Shahan Prairie area, and along Oak Point’s winding lakefront roads all deal with the same aggressive Blackland Prairie clay. That clay is the reason a gate installed three years ago can suddenly start scraping the ground. We work with that soil reality, not against it.
Why Gatewood Fence & Gate Is Oak Point’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001, and the name hasn’t changed on the door. When you call for Gate Parts & Welding work in Oak Point, you’re not getting a rotating cast of strangers. You’re getting Hal and his crew, people who show up in uniform, with background checks done, and who have likely worked on a gate identical to yours somewhere else along Lake Lewisville’s eastern shore.
Our Oak Point customers call us because the gate is a statement on these properties. These aren’t cheap builder-grade gates. They’re custom ornamental steel and wrought iron, often eight or ten feet tall, sometimes on underground operators. That kind of gate needs a welder who respects the material. We weld on site, in your driveway, so the gate never leaves your property. Hal’s 90-Day Done Right Promise comes in writing on every invoice. If something isn’t right, one call brings him back. No runaround. No fine print.
And the phone works. A live person answers 24/7, not a voicemail, not a transfer queue. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Our Gate Parts & Welding Services in Oak Point
Hinge Replacement
In Oak Point, a gate doesn’t sag in the middle. It sags at the hinge post. When the clay heaves, the post tilts, and suddenly the hinge pin is carrying load it was never meant to carry. We replace hinges by first checking the post itself. If the post is even 3/4 inch out of plumb, new hinges won’t fix it for long. Most hinge replacements on ornamental gates in this area run $180-$340, including realignment of the hinge post and re-welding the hinge mounts where needed.
Post Replacement
Oak Point’s soil is the main character in most post replacement jobs. The Blackland Prairie clay near Lake Lewisville swells hard in wet winters and then cracks open in summer drought. That cycle torques gate posts out of the ground, leaning them inches over a few years. A proper post replacement means digging deeper than the original builder bothered to go, setting the post with a wider concrete collar, and sometimes adding drainage gravel at the base. Full post replacement with concrete work on a heavy ornamental gate in Oak Point typically runs $450-$850 per post.
Rail Repair
When a gate post leans, the rails take the stress next. Bent or cracked rails on double swing gates are common around Oak Point because the two leaves stop meeting square. We straighten, reinforce, or replace top and bottom rails as needed, then re-hang the gate so it stops fighting itself. Rail repair on standard ornamental gates usually runs $150-$400 depending on whether we’re welding a cracked joint or replacing a full rail section.
Custom Welding
This is where Hal does his best work. Oak Point homeowners often can’t buy a replacement panel or finial because the original gate was custom built for the house. That’s fine. We weld on site, match the existing scrollwork and bar spacing, and blend the repair so it doesn’t look like a patch. Custom welding work ranges from $120 for a small bracket repair to $400-plus for extended fabrication on ornamental pieces. We’ll give you a written price before striking an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Oak Point
We’re certified to service nine major gate opener brands, and in Oak Point we see a lot of LiftMaster operators on these custom swing gates, plus FAAC and Linear units on older Gate Installation - Oak Point. If your gate motor is acting up after a post shift, we don’t just swap the operator. We check the gate’s alignment first, because an operator struggling against a misaligned gate will fail early. We keep common FAAC and Linear parts on the truck, which means fewer return trips and less waiting for your gate to work again.
Common Gate Parts & Welding Problems We See in Oak Point Homes
- Gate post heave after wet winters. The clay near Lake Lewisville absorbs water and swells, lifting post footings up to two inches in a single season. That twists the hinge post, the gate leaf drags, and the operator starts pulling more amps until it burns out. We see this on gates only 3-5 years old.
- Rust seizure on ornamental iron near the lake. Oak Point’s localized humidity accelerates surface rust on decorative gate hinges and latch pins. What starts as a stiff latch becomes a seized mechanism that won’t let the gate close. We replace hinge pins and re-machine latch points, then treat the metal to slow the next cycle.
- Loop detector failures after soil shift. When a gate’s swing arc changes because a post moved, the vehicle crossing the loop detector no longer lines up with the sensor coil. Your gate may sit open, or refuse to close, even though the opener reads fine. We recalibrate the swing arc against the loop after any post realignment.
- Cracked weld joints at stress points. On heavy custom gates, repeated cycles with a misaligned post concentrate stress at upper hinge welds and mid-rail joints. The crack starts small, then propagates. We grind out the failed weld, bevel the joint, and lay down a proper fillet that matches the original penetration. Fixing the weld without fixing the post means you’ll fix it twice.
Pricing for Gate Parts & Welding in Oak Point, TX
Here’s what you can expect in Oak Point based on the work we commonly do around the lake:
- Hinge replacement with post realignment: $180-$340 per hinge post
- Full post replacement with concrete and drainage prep: $450-$850 per post
- Rail repair or straightening: $150-$400
- Custom welding (brackets, finials, scrollwork, patch panels): $120-$400
- Operator recalibration after post realignment: $90-$200
You’ll get the exact number before we start. Not after. We quote the job in writing, you approve it, then we work. No trip charge inside the county. And if you have a written estimate from anyone else, we’ll give you a free second opinion on it. Seniors and veterans take 10% off permanently. If a repair lands over $200, take $40 off. One discount per job, applied automatically when it applies.
Call (979) 291-0947 and we’ll walk the gate with you.
We Also Serve Cities Near Oak Point
Besides Gate Parts & Welding in Oak Point, our crews run daily through Prosper, Plano, Allen, and Frisco. Same welders, same written pricing, same 90-Day Done Right Promise. If you’re just outside Oak Point and the gate is dragging, call and we’ll have someone out.
Serving Oak Point, TX - Our Local Coverage Area
We’re based in the Oak Point area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Oak Point
Your gate is sagging because the hinge post has moved, not because the gate itself failed. Oak Point sits on Blackland Prairie clay that swells in wet weather and shrinks in drought, and near Lake Lewisville that movement is aggressive enough to shift a post several inches within three to five years. We fix the post first, then re-hang and weld the gate. Call (979) 291-0947 for a free assessment.
Yes, in most cases we can. We cut out the bent section, straighten or replace the affected rail or picket, and weld the new piece in while the gate hangs in place. The repair won’t be invisible, but it will be strong and clean. Full replacement is rarely necessary unless the damage is extensive. Call (979) 291-0947 and we’ll tell you straight.
We can, and often it makes sense to do both in one visit. If our Gate Motor & Opener in Oak Point has been fighting a misaligned gate, the motor and limit switches may already be tired. We’ll check the operator’s condition while we realign the post, and give you a separate written quote if a replacement is warranted. Estimates are free, so call (979) 291-0947.
It can be. Saturated clay conducts moisture into the post and foundation areas, and if the soil shift moved your gate even slightly, Gate Access Control in Oak Point may be stalling against a bind it didn’t have before the rain. The error is usually the operator sensing overcurrent. We’ll assess the gate alignment and the electrical connections. Call (979) 291-0947 to get it sorted.
We set the post deeper than the original, use a wider concrete collar, and add drainage gravel at the base so water doesn’t pool against the footing. That combination slows the heave cycle significantly. It won’t stop Texas clay from moving entirely, nobody can promise that, but it dramatically reduces the recurrence rate. Call (979) 291-0947 if your post is already leaning.
When your gate is dragging, binding, or hanging crooked, don’t wait until the operator burns out or the post tears loose. Call Gatewood Fence & Gate at (979) 291-0947. We’ll come out, look at your gate in Oak Point, hand you a written price, and get to work if you approve it. Hal’s name is on the shop, and the 90-Day Done Right Promise is on your invoice.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Oak Point and surrounding communities since 2001.