Ghost Controls Gate Repair Service Nationwide | Gatewood Fence & Gate

Why Prosper Homeowners Choose Ghost Controls Gate Repair

We provide independent Prosper Ghost Controls service in Texas - openers, arms, control boards, keypads, solar systems, the works. We stock the exact torque limiters, control boards, and gear kits for AXDP, TDS2, and HYPRO models, so we’re not waiting on manufacturer lead times or charging manufacturer markup. As an independent Ghost Controls service provider, we’re not affiliated with or authorized by Ghost Controls, but we work on their equipment daily across Prosper’s large-lot neighborhoods. Call (979) 291-0947 and you’ll get Hal Gatewood or someone from his crew, not a recording.

Call (979) 291-0947

What makes our Ghost Controls work different comes down to this: we’ve been fixing gates in and around Plano and Prosper since 2001, back when this whole area was still mostly pasture. Hal Gatewood picked up the trade at Collin College over in McKinney, went through their welding and construction technology program, and never really looked back. Most folks out here in Gentle Creek, Star Trail, and the surrounding neighborhoods know Hal because he showed up after some other outfit left a gate motor wired wrong and a hinge set crooked, and he cleaned it up without making a big deal of it.

Why Trust Gatewood Fence & Gate for Your Ghost Controls Gate Repair?

Here’s what we know about Ghost Controls equipment: it’s decent hardware that gets installed wrong or maintained poorly, and then it fails in ways that other shops misdiagnose. We see the same failure patterns week after week - a TDS2 arm clicking and slipping because the gate leaf sagged past the torque limiter’s tolerance, an AXDP2 that won’t auto-close after dusk because the solar regulator stopped holding float voltage, a HYPRO2 board that welded a relay shut after a low-battery startup surge. We know these units because we open them up, trace the circuits, and fix the actual fault rather than throwing a whole new opener at the problem.

Hal Gatewood’s name is on the shop and on every invoice. He’s been owner-operated since 2001, with a published address and license number anyone can look up. That’s not a marketing line; it’s the oldest accountability there is. If we tell you a Ghost Controls board needs replacing, we’ll show you the failed channel on the board before we quote the part. If we tell you the arm is fine and the post is the problem, we’ll put a level on the post and show you that too. Every job carries our 90-Day Done Right Promise in writing: if it’s not done right, we make it right.

Common Ghost Controls Gate Repair Problems We Fix in Prosper

• AXDP Series (AXDP2/AXDP4) - solar-charging regressions and dead batteries. The AXDP2’s factory solar regulator sometimes stops holding the battery above 11.8V, especially after a power blip resets the controller’s charge logic. The gate works fine all summer, then suddenly won’t auto-close after dark in October. We swap in a 10A MPPT regulator and load-test the battery before we blame the board.
• TDS2 Series (TDS2OPEN/TDS2SOLO) - torque limiter clicking and slipping. When the gate leaf sags more than 1.5 inches off level, the TDS2 arm’s torque limiter clicks and jerks near the closed position, and the gate stalls or reverses. The fix is rarely a new arm. In Prosper’s clay soil, the real culprit is usually a post that’s drifted out of plumb and pulled the hinge geometry with it.
• HYPRO Series (HYPRO2/HYPRO4) - control board relay failure. The HYPRO2 has a known failure mode where repeated low-battery startup surges weld a relay shut and the gate stops mid-travel. You’ll hear the board click but the arm won’t move. We test the relays individually before we condemn the board; sometimes a $20 relay replacement beats a $200 board swap.
• Wireless keypad (WKP) desync after storms. North Texas thunderstorm season knocks Ghost Controls keypads offline. Lightning strikes or close-range powerline interference break the sync between the WKP receiver and the transmitter. The keypad shows a solid red light but won’t trip the opener. We re-pair the keypad at the receiver, then test the learning button on the board itself before we advise anything more involved.
• Post shift and hinge alignment problems. Prosper sits on Blackland Prairie clay that swells and shrinks with every wet-dry cycle, and a gate post that shifts 3-5 degrees throws every Ghost Controls arm, sensor, and limit switch out of alignment. We weld on site, realign the post, repair the hinge set, and only then dial in the opener.

The soil here is a real factor. Local gate techs know that concrete footings poured for residential swing-gate posts in Prosper’s clay-heavy ground often start tilting within three to five years because the original contractor didn’t dig deep enough to get below the active soil zone. So a Ghost Controls gate that “just won’t close right” almost always needs a post realignment or re-pour before any operator or hinge work will hold. Fix the panel without the post and you’ll fix it twice.

Ghost Controls Parts & Our Repair-vs-Replace Approach

We install genuine Ghost Controls boards, arms, and gearboxes when a repair has to match the controller’s timing and the manufacturer’s warranty terms. But we don’t blindly buy OEM for everything. Ghost Controls marks up some wear parts heavily, and for older units the OEM magnet, capacitor, or solar regulator isn’t always the best value. In those cases we substitute industrial-grade aftermarket parts - magnets, capacitors, solar regulators - from suppliers we’ve tested on our own jobs for years. The part is just as good, and you keep the difference.

Our rule on replace-vs-repair is simple: we replace only when the arm’s internal gear teeth are stripped beyond a 30-minute rebuild or the board has two failed channels. Anything short of that, we repair. We stock locally what we need for fast turnaround on the common Ghost Controls failures - torque limiters for TDS2, control boards and relays for HYPRO2, regulators and batteries for AXDP solar systems. Call (979) 291-0947 and we’ll quote the repair and the replacement side by side so you can see the difference.

Our Ghost Controls Service Process - Step by Step

1. 1
   Diagnosis. We start at the post, the hinge, and the gate’s travel arc before we open the opener. A gate sags in the hinge post, not in the middle, and that determines everything downstream. We load-test the battery, check the regulator’s float voltage, and run the arm through its full cycle with the leaf disconnected if needed.
2. 2
   Repair or install. We replace only what’s failed. If it’s a board relay, we swap the relay. If it’s a torque limiter, we rebuild it. If the post has shifted, we weld it true and re-set the footings before the opener goes back on. For installs, we measure the gate’s throw, weight, and wind load, then spec the opener and arm accordingly.
3. 3
   Test and re-sync. We run the gate through 20-plus cycles, test the safety edges, re-sync your WKP keypad and remotes, and verify the auto-close timer and force settings match the manufacturer’s spec for your arm length. Then we call you over and show you the gate working.
4. 4
   Warranty. Every job carries our 90-Day Done Right Promise in writing. If something we touched fails inside 90 days, one call brings Hal or his crew back. No runaround, no service ticket queue.

Ghost Controls Products We Service & Install in Prosper

We service and install the full current Ghost Controls lineup and most legacy units still in the field: AXDP Series (AXDP2, AXDP4), TDS2 Series (TDS2OPEN, TDS2SOLO), HYPRO Series (HYPRO2, HYPRO4), and the GHOST-CONTROLS Gate Opener Kit with Solar Compatibility. That covers swing and slide applications on single and dual leaves, with solar, battery backup, and transformer-powered configurations. We also handle the wireless keypad (WKP) and remote programming for all the above. For local stock we keep the common wear-and-failure parts on hand - torque limiters, control boards, regulators, batteries, keypads, and remotes - so most Prosper service calls are same-trip fixes, not two-week waits.

We Also Service These Brands

Gate Repair is our specialty - Ghost Controls is one of nine brands we’re certified to service: LiftMaster, FAAC, BFT, Linear, Viking, DoorKing, Elite, and Mighty Mule. If you’ve got a Mighty Mule on one gate and a Ghost Controls on the other, we handle both in one visit.

FAQs - Ghost Controls Gate Repair Service in Prosper

Book Your Ghost Controls Service in Prosper, TX

Call (979) 291-0947 and a live person answers, day or night. We’ll get your gate fixed, warrant it in writing for 90 days, and quote the price before we start. Hand me your number and I’ll call you before I pull up - that way you’re not standing in the driveway waiting on me.

Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Prosper since 2001.