Ghost Controls Keypad & Intercom Repair Nationwide | Gatewood Fence & Gate

Ghost Controls Keypad & Intercom Repair: The Prosper Owner’s Guide

Ghost Controls keypad and intercom repair in Prosper typically runs between $185 and $420 installed, depending on whether we’re swapping the keypad face, replacing the intercom module, or rewiring the whole entry station. We stock Ghost Controls-compatible keypads and intercom parts on the truck, so most repairs happen the same day we show up. The usual story: you punch in your code, nothing beeps, or the intercom crackles like a bad radio station, and now you’re walking out to the gate in the rain to let a delivery driver in.

Call (979) 291-0947

Most folks in Prosper discover the part has failed the hard way – they’re standing at the gate at 10 p.m. trying to remember if they reset the code, or a guest buzzes the intercom and gets static while the gate just sits there. Here’s what we’ve learned fixing Ghost Controls entry systems around Prosper since before half these neighborhoods had streetlights: the keypad and intercom are usually the first things to go, not the motor. They sit out in the sun, the rain, the freeze-thaw cycles, and every door-to-door salesman who jabs the buttons like it owes him money.

Key Takeaways:

• We keep Ghost Controls keypad and intercom parts on the truck for same-day repair in Prosper
• Installed pricing is quoted and agreed before we touch a single wire – no surprises at the door
• Every repair carries our 90-Day Done Right Promise in writing
• Ghost Controls parts fail more often from weather exposure than from electrical faults

Which Ghost Controls Models This Applies To

We work on the full Ghost Controls lineup: the AXDP and AXP series openers, the TSS1 and TDS2 keypad models, and the wireless intercom kits Ghost Controls sells as add-ons for residential gates. The keypad compatibility gotcha most Prosper homeowners run into is this: Ghost Controls keypads come in two voltage configurations, and the older AXDP series used a different wiring harness than the newer AXP line. If you buy the wrong one online, it looks identical in the photo but won’t talk to your control board. We match the part by the model sticker on the back of your existing keypad – it’s usually faded to nothing, so we bring a magnifier and a flashlight.

For Ghost Controls specifically, we prefer OEM keypads and intercom modules over aftermarket equivalents. The aftermarket units work, but the button membranes are thinner, and in Texas heat they crack along the edges within two summers. An OEM Ghost Controls keypad costs maybe $40 more than the knockoff and lasts four to five years longer. That’s a trade we’ll tell you about face to face, then let you decide.

We also keep parts for LiftMaster, Mighty Mule, and DoorKing on the truck, but Ghost Controls is its own animal when it comes to keypad wiring colors. If you’ve got a faded red wire where the diagram says green, don’t guess. We’ve seen too many boards fried by a well-meaning afternoon of trial and error.

Signs Your Ghost Controls Keypad & Intercom Is Failing

• Keypad lights up but won’t accept the code. This is usually a failing membrane switch under the buttons – the tactile layer wears out and the digits stop registering. We see it a lot on gates that face west and bake in the afternoon Prosper sun.
• Intercom rings but you can’t hear anyone (or they can’t hear you). The speaker and mic sit behind a tiny grille that fills with dust and dead bugs. Once moisture gets in, the audio board corrodes and you get that crackling half-sound.
• Keypad works with the gate open but not closed. That’s almost always a wiring issue at the gate hinge point, not the keypad itself. The wire flexes every time the gate cycles, and after a few thousand cycles the copper strands break inside the insulation.
• Buttons stick or you have to press twice. The silicone overlay on Ghost Controls keypads breaks down in UV light. Once the buttons lose their snap, water starts getting behind the faceplate and the board underneath is on borrowed time.
• Intercom works during the day but dies at night. That’s condensation. Prosper gets cool nights even after hot days, and the temperature swing pulls moisture into the housing. A small weep hole in the right spot usually fixes it – but drilling one in the wrong spot floods the board.

Replacement Cost & What’s Included

Here’s what Ghost Controls keypad and intercom repair costs in Prosper, installed:

The range depends on what we find when we open the housing. A clean swap with intact wiring runs on the low end. If the previous installer left the wire nuts exposed and the connections are green with corrosion, we’re splicing and heat-shrinking before we mount the new part, and that adds labor. Every price is quoted and agreed before we start – you’ll know the number before we pick up a screwdriver. The part carries its manufacturer warranty, and our labor carries the 90-Day Done Right Promise. If it isn’t done right, one call brings us back.

DIY or Call Us?

You can safely check a few things before picking up the phone. Make sure the keypad isn’t just in a low-battery state if it’s a wireless model – the Ghost Controls wireless keypads use a 9-volt that dies quietly. Check that the intercom’s power supply hasn’t tripped at the outlet. If you’re comfortable with a multimeter, you can verify there’s 12 to 24 volts DC at the keypad terminals. Those three checks answer half the calls we get.

Where DIY goes sideways is inside the keypad housing. Ghost Controls boards are sealed, and prying the faceplate off without cracking the gasket voids any chance of a clean repair. The wiring runs alongside the gate opener’s high-voltage feed in some installs, and crossing the low-voltage keypad wires with a live motor lead will smoke the control board – that’s a $400 mistake disguised as a $12 fix. If the keypad isn’t responding after the basic checks, call us at (979) 291-0947. We’ll be out the same day in most of Prosper.

FAQs