FAAC Gate Installation Nationwide | Gatewood Fence & Gate

FAAC Gate Installation in Prosper: What to Know First

We install and service FAAC gate operators throughout Prosper, TX, from simple swing gates in Gentle Creek to heavier sliding and double-gate setups on acreage off Preston Road. Most FAAC installations take one full day on site, and we quote the job before any work starts so the number we give you is the number you pay. If you’ve got a FAAC operator still in the box or one that’s been limping along, call (979) 291-0947 and we’ll tell you straight what it needs.

Call (979) 291-0947

This page is for Prosper homeowners who own FAAC equipment and want a crew that actually knows the brand: how its motors behave in Texas heat, which models have known board issues, and what’s worth fixing versus replacing. Hal Gatewood has been working on FAAC gates in this area since 2001, and we’re independent, which means we don’t answer to a manufacturer’s script.

How FAAC Products Fail - and How We Fix Them

FAAC builds solid equipment, but every brand has its weak spots. Here’s what we routinely find on FAAC jobs around Prosper, and what we do about it.

• Leaf delay switches on older swing operators. On FAAC C720 and S700 series swing arms, the leaf delay switch gets dirty or corroded from North Texas dust and starts reading a gate that’s mid-swing as a gate that’s fully closed. Symptom: one leaf stops halfway and the opener blinks like it’s finished. We open the arm, clean and reseat the switch contacts, and if it’s worn past that, we replace the switch rather than the whole arm. Some companies throw a new arm on because it’s easier for them. That’s a thousand-dollar shortcut.
• Sensitivity pots losing their setting in temperature swings. FAAC 412 and 415 boards use manual trim pots for force and speed. In Prosper, where a February morning can be 28 degrees and an August afternoon 104, those pots drift. The gate starts slamming or reversing for no reason. We reset the pots, run the gate through a full cycle under load, and if they drift again, we replace the pot set on the board, which keeps your operator original and keeps the repair under two hundred dollars instead of a board swap.
• Belt wear on FAAC 844 sliding gate operators. The 844 series uses a belt drive inside the operator housing, and when that belt gets loose from years of stop-start cycles, the gate gets jerky near the end of travel and the motor works harder than it should. We catch this on installations where homeowners say the gate “just doesn’t feel smooth anymore.” Tightening the belt tensioner is a routine adjustment, but we check the belt teeth for cracking while we’re in there. A thirty-dollar belt now beats a stripped drive gear later.
• Photocell alignment drift on new concrete. Prosper sits on expansive clay soil. When new concrete driveways settle or heave, the FAAC photocell posts shift a fraction of an inch and the gate starts refusing to close. We see this on installs that were done right but on posts set without enough depth. We re-bed the post or shim the photocell mount, then test the safety reverse under real sunlight, which matters more than people think with FAAC’s older red LED photocells.
• Bad connections at the terminal block from rushed installs. This one’s not FAAC’s fault, but it shows up on FAAC jobs all the time. A previous installer strips the wire ends too long, leaves copper exposed, and a single strand touches the next terminal. The gate works for a week, then a rain settles the dust into that gap and the thing shorts intermittently. Hal has fixed more of these than he can count, including one on a C721 in Gentle Creek where the homeowner had been told she needed a new control board. She didn’t. She needed someone to strip the wire properly and tighten the screws.

Our FAAC Gate Installation Process

1. 1
   You call and a person answers. Not a voicemail. Not a menu. We ask what kind of gate, what kind of operator, and what it’s doing or not doing. We set a window and we keep it.
2. 2
   We show up and look at the whole thing. Gate, posts, hinges, operator, wiring, the run from the house power. On a FAAC install we’re looking at how the gate was hung before we ever power on the operator, because a gate that isn’t balanced will eat a FAAC motor in eighteen months no matter how good the install. We check post plumb, hinge play, and the gate’s swing weight. If the gate sags, we fix that first or the install won’t last.
3. 3
   We make the parts call with you. For warranty work we use FAAC OEM parts. For out-of-warranty repairs, we’re honest about when a quality aftermarket part does the job and saves you real money, and when it doesn’t. The decision is yours, with our straight answer on what we’d put on our own gate.
4. 4
   We install and test under actual conditions. We run the gate through full open and close cycles with the wind blowing, which in Prosper means a real wind test about half the year. We set the force low enough that it reverses on actual resistance, not on the manufacturer’s starting spec, because a FAAC operator set too hot will pin a kid or a dog before the safety photo eyes ever see it.
5. 5
   We walk the job with you before we leave. We show you the operator working, point out the photocells, show you how to put it in manual if the power goes out, and answer any question you’ve got. You’re not left with a gate that works and no explanation of it.
6. 6
   You get the 90-Day Done Right Promise in writing. If anything we touched isn’t right, one call brings us back. No runaround, no “that’s not covered.” Hal’s name is on it.

What FAAC Gate Installation Costs in Prosper

Every job prices differently, but we quote it before we start and the number doesn’t move unless you change the scope yourself. Here’s what FAAC work in Prosper typically runs:

• FAAC operator install (labor only, operator supplied): $450-$850 depending on single swing, double swing, or sliding, and how much wiring work is involved.
• New FAAC swing gate package, complete: $3,200-$5,500 for a single swing, including gate, operator, posts, hardware, and install. Double swing runs higher because of the second leaf and the coordination logic.
• FAAC sliding gate package, complete: $3,800-$6,000 depending on gate size, track or cantilever setup, and power run distance from the house.
• FAAC board replacement or repair: $180-$420 parts and labor, depending on the board model and whether we’re swapping or repairing the existing board.
• Photocell replacement or re-alignment: $95-$180, and it’s often the cheapest fix that gets a reluctant gate closing again.

What moves the price: whether the gate was hung level in the first place, how far the power run is, whether we’re fighting someone else’s old wiring, and what the soil is doing under your posts. Call (979) 291-0947 for a free estimate on your specific gate. We’ll tell you what it costs before we lift a tool.

Why Prosper Homeowners Call Gatewood Fence & Gate for FAAC Work

Hal Gatewood has been fixing gates in and around Prosper since 2001, back when this whole area was mostly pasture and everybody knew everybody at the Kroger on Preston Road. He picked up the trade at Collin College over in McKinney in their welding and construction technology program, and he’s still the one who answers the phone at three in the morning when your gate won’t close and the dog is making a break for it. That’s the difference: when you call Gatewood Fence & Gate, you get a company whose owner lives with his name on the shop and his address published. We weld on site, so your gate never leaves your driveway unless it absolutely has to. We work on nine major brands, so if we’re out for FAAC work and we spot a LiftMaster or Mighty Mule, Ghost Controls, or DoorKing motor on another gate, that’s not a mystery to us, it’s a Tuesday. Most important: every job we do carries the 90-Day Done Right Promise, written down. We don’t hide behind fine print. If it’s not done right, we make it right. Hand me your number and I’ll call you before I pull up, that way you’re not standing in the driveway waiting on me.

FAQs