Ghost Controls Welding & Fabrication Nationwide | Gatewood Fence & Gate

Ghost Controls Welding & Fabrication: The Prosper Owner’s Guide

Most Ghost Controls gate systems that need welding work in Prosper run between $180 and $400 for a typical bracket repair or post reinforcement, and we can usually get to you the same day when a gate is down or dragging. The part we’re usually welding is either the mounting bracket assembly that holds the arm to the gate, or the gate post itself where the hinge hardware has torn loose. You’ll know it when you hear a grinding pop followed by the gate sagging an inch lower than it sat last week.

Call (979) 291-0947

We stock Ghost Controls-compatible brackets, hinge plates, and post repair sleeves on the truck, and we weld on site so your gate never leaves your property. Hal Gatewood has been doing this work in Prosper since 2001, and he’ll tell you straight: most welding repairs on Ghost Controls setups are the result of a hinge post that was never set deep enough in the first place, or a bracket that got wallowed out because the gate was out of balance.

Key takeaways:

• Ghost Controls welding repairs in Prosper typically run $180-$400 installed
• We stock the common Ghost Controls bracket and hinge parts on the truck
• Same-day service is available when your gate is down or won’t close
• Every weld carries our 90-Day Done Right Promise in writing
• Price is quoted and agreed before any work starts, always

Which Ghost Controls Models This Applies To

Gatewood Fence & Gate is an independent shop, not affiliated with Ghost Controls, but we service their full residential line: the AXDP and AXD dual-swing arm kits, the RVS single-arm ram, and the older TSS1 and TDS2 series that are still running on a lot of Prosper properties. The welding points are almost always the same across models: the post-mount bracket where the arm attaches, the gate leaf bracket, and occasionally the hinge side of the post assembly.

Here’s the gotcha most owners miss: Ghost Controls uses a specific bolt-hole pattern on their post-mount brackets, and it’s not the same as what LiftMaster or Mighty Mule use. If somebody welds a generic bracket from the shelf at a big box store, the arm geometry shifts and the opener fights itself until it burns out. We match the bracket to your Ghost Controls model, and if a genuine Ghost Controls part isn’t available quickly, we’ll tell you that upfront and use a machined aftermarket equivalent that matches the hole pattern and arm plane exactly. Hal would rather you wait a day for the right part than weld on something that’ll chew through your gearbox in a year.

Signs Your Ghost Controls Welding & Fabrication Is Failing

• The gate sags toward the latch side and scrapes the ground. This is almost always the hinge post leaning or the hinge welds cracking at the post face. A gate sags in the hinge post, not in the middle, and that’s where we start.
• You hear a popping sound when the opener starts or reverses. That pop is the bracket flexing against a cracked weld. The arm pushes, the weld flexes, and every cycle makes the crack longer until it tears out completely.
• The gate shudders halfway through the swing. When a hinge weld starts to fatigue, the gate doesn’t track in a clean arc anymore. It binds slightly, the opener strains, and the shudder is the motor compensating for a mechanical bind.
• The arm bracket sits at a slight angle it didn’t have before. Ghost Controls arms are designed to run level with the gate plane. If the bracket has pulled even an eighth of an inch off square, the arm can bind and the unit will throw an obstruction error or overheat.
• Rust staining runs down from a weld point. In Prosper’s freeze-thaw winters and humid springs, a crack in a weld lets water in, and rust bleeding out of the joint is the tell. By the time you see the stain, the weld has been compromised for a while.

Replacement Cost & What’s Included

In Prosper, you’re looking at $180 to $240 for a single bracket reweld or replacement on a Ghost Controls swing arm, $250 to $350 when a hinge post needs to be cut, sleeved, and rewelded at the base, and $350 to $400 when we’re reinforcing or replacing a post that’s rotted at ground level. If both hinge points are compromised, it lands on the higher end because we’re working both sides to keep the gate plane true.

Every quote includes the part, the labor, the welding time, and cleanup. We don’t add trip charges inside the county, and the price Hal quotes before he starts is the price on the invoice when he leaves. Seniors and veterans get 10% off permanently, and there’s $40 off any repair over $200. If you’ve got a written estimate from another shop, bring it over and we’ll give you a free second opinion on it. The 90-Day Done Right Promise covers every weld: if it fails because of our workmanship, we come back and fix it, no runaround.

DIY or Call Us?

Here’s where a lot of people get hurt: a Ghost Controls gate arm is under constant tension, and a cracked weld can let go without warning while you’re under it with a grinder. If the opener is still powered when you start prying on a bracket, you’re asking for a broken hand or worse. We say this not to scare you but because we’ve pulled too many gates off people who thought they’d save a Saturday.

What you can safely check is the play: with the opener disengaged, lift the gate at the latch side and watch the hinge post. If the post moves with the gate, that’s a weld or footing problem, not a hinge problem. You can also mark the bracket position with a pencil and run the gate twice to see if the bracket shifts. Beyond that, call someone who welds gates for a living, not someone who welds as a hobby. That’s us: (979) 291-0947. Hand me your number and I’ll call you before I pull up - that way you’re not standing in the driveway waiting on me.

FAQs