Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Motor & Opener in Prosper: What to Know First
We repair and install Ghost Controls gate motors and openers throughout Prosper, and most jobs are done the same week we get the call. You’ll get a straight answer on price before any work starts, because we quote the job first and we don’t change the number at the door. We’re an independent Ghost Controls service provider, which means we work for you, not the manufacturer.
If you own a Ghost Controls opener and it’s acting up, doing nothing, or starting and stopping mid-cycle, this page will tell you what’s actually going on with it. And if you’d rather skip the reading, call Hal at (979) 291-0947 and he’ll talk you through it. A live person answers, 24 hours a day.
How Ghost Controls Products Fail - and How We Fix Them
Ghost Controls builds a solid opener for the money, especially on swing gates. But we see the same handful of problems repeat themselves across Prosper neighborhoods like Gentle Creek, Windsong Ranch, and Light Farms. Here’s what’s actually happening when they stop working:
- AXDP and AXD series: dead control board after a storm. Prosper gets real lightning, and the Ghost Controls AXDP board doesn’t always forgive a nearby strike. The opener will have power but won’t respond to remotes or the push-button. We test the board, confirm it’s the surge path, and replace it. If your panel outside is still good, we’re not going to sell you a whole new opener. That’s the repair-first part of what we do.
- TSS1 and TDS2 swing openers: motor runs but the gate doesn’t move. Nine times out of ten it’s a sheared limit nut or a stripped drive gear, not a dead motor. This is the one we find most after another outfit told somebody they needed a complete replacement. We open the unit, pull the gear, and replace what’s actually worn. Often the motor itself has years left in it.
- Rust at the mounting plate and arm assembly. Ghost Controls powder coating on the opener body is decent, but the bolt heads and pivot points on the mounting hardware take on water in our clay-heavy Prosper soil. When the arm binds, the board senses an overload and throws an error code, so the gate stops halfway. We pull the hardware, replace it with better-sealed fasteners, and grease the pivot properly. That usually clears the false overload.
- Range and intermittent response from the remotes. The ABBT2 and GMT receiver is fine, but many Prosper homes mount the receiver box behind a brick column or a metal fence panel, which eats the signal. We relocate the antenna or add a simple external antenna wire to the receiver, and the range comes right back. It’s a $40 fix that feels like a $400 problem.
- Solar or battery-backup Ghost Controls setups on pasture gates. Lot sizes in unincorporated Prosper and over toward Celina mean some Ghost Controls systems run on solar charging with a battery in the loop. When the battery is past its useful life, the opener works fine with full sun but won’t hold through the night or a cloudy stretch. We test the battery under load, replace it if it’s done, and check the panel wiring. We don’t sell a new opener for that, either.
Our Ghost Controls Gate Motor & Opener Process
This is how every Ghost Controls job goes at Gatewood Fence & Gate, from the first call to the last look-over:
- 1
Call us at (979) 291-0947. You reach a person. You describe the symptom. We’ll ask what the opener is doing, or not doing. Sometimes we save you the trip charge right there on the phone.
- 2
We come out and look. Hal or one of his guys comes to your property in Prosper, checks the opener, the arm, the limit settings, the condition of the gate itself, and the power feed. We don’t stop at the symptom. We trace it to the cause.
- 3
We quote it in writing. You get an upfront price. It’s the price. If it’s over $200, the $40 repair discount comes off automatically, and seniors and veterans get their 10% off, too. No haggling.
- 4
We fix it, usually on the spot. We stock common Ghost Controls parts, including boards, gear kits, remotes, and hardware. If it’s a welded field repair, we have the welder on the truck. Your gate stays in your driveway.
- 5
We test it like we own it. We run the full cycle several times, check the safety edges and photo eyes, and watch the limits. Then we show you the problem and the fix so you know what you paid for.
- 6
We hand you the 90-Day Done Right Promise. It’s in writing on every job. If it’s not right, one call brings us back. No runaround, no argument, no extra charge.
What Ghost Controls Gate Motor & Opener Costs in Prosper
Numbers here are honest ranges based on what we’ve billed on Ghost Controls jobs around Prosper over the last few years. Your exact price depends on your opener model, the condition of the gate itself, and whether we’re doing a component repair or a full replacement.
| Ghost Controls Scenario | Typical Price Range |
|---|---|
| Service call and diagnostic (in-county) | Free, no trip charge |
| TSS1/TDS2 gear or limit nut replacement | $185 - $310 |
| AXDP control board replacement | $240 - $380 |
| Full opener swap (unit + labor + hardware) | $850 - $1,450 |
| Receiver relocation or remote pairing | $65 - $145 |
| Battery backup replacement | $130 - $250 |
What moves the price most is the gate itself. If the gate sags in the hinge post, no new opener will run right until the gate is balanced. We’ll tell you that before you buy a motor. And we never start a repair until you’ve approved the number. Call (979) 291-0947 for a free estimate on your Ghost Controls opener.
Why Prosper Homeowners Call Gatewood Fence & Gate for Ghost Controls Work
Hal Gatewood’s name is on the shop, and the shop is down the road. He’s been fixing gates around Prosper and Collin County since 2001, before half these neighborhoods existed. Any other gate company can say they know openers. We’re the ones who actually stock Ghost Controls boards and gears, know the false-overload codes, and won’t try to sell you a $1,200 replacement because of a $30 limit nut.
Every job carries the 90-Day Done Right Promise in writing. A live person answers the phone at 2 p.m., and at 2 a.m. We service nine major brands, including LiftMaster, Mighty Mule, and DoorKing, so when a Ghost Controls system genuinely isn’t worth repairing, you get a real recommendation about what to switch to. Not a sales pitch. Just what we’d do if it were our gate.
FAQs
We install and service Ghost Controls openers as an independent provider, which means warranty claims go through Ghost Controls directly. We’ll help you with documentation and we’ll tell you honestly whether the failed part is likely to be covered. If the part is still under warranty, we can install it for you; the labor on that part is not on Ghost Controls, so we quote that separately and up front.
For most Ghost Controls repairs in Prosper, we’re on the property within one to two business days. If your gate is stuck open or stuck shut, tell us when you call; Hal keeps buffer time for exactly that, and he’ll tell you straight when he can have somebody there.
Sometimes, yes. It depends on what the day looks like and how far you are from the shop. Call (979) 291-0947 and ask. The person on the other end will tell you honestly whether it’s today or tomorrow, and Hal will call you before he pulls up so you’re not standing in the driveway waiting on him.
If your opener is a Ghost Controls TSS1, TDS2, or AXDP from about 2015 or newer, it’s worth repairing in most cases. Boards, gears, and remotes are available and affordable. If the unit is older, water-damaged inside, or smoking, we’ll tell you that a repair is throwing good money after bad. We don’t make that call lightly, and we don’t make a commission on selling you a replacement.
Yes. If your Ghost Controls opener runs through a keypad, a phone entry system, an intercom, or a camera at the gate, we can wire and troubleshoot that integration. One thing to know: if your access control is controlled by an HOA or a community system, we’ll need whoever manages that software to release the signal, but we can still test, install, and repair the hardware side of it.
A full installation includes the opener, the mounting hardware, the power feed wiring, safety edges and photo eyes, the arm, and complete setup and testing. It also includes us telling you if the gate is too heavy or too unbalanced for that opener; we won’t put a motor on a gate that will destroy it in a year. We quote the full job up front, and we don’t add anything to the bill after the work starts.
Call Gatewood Fence & Gate for Ghost Controls Opener Work in Prosper
If your Ghost Controls opener is giving you trouble, call Hal at (979) 291-0947. You’ll speak to a live person, you’ll get a straight answer, and we’ll show up in the window we give you. Free estimates. No trip charge inside the county. The name is on the shop.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Prosper and nearby areas.